/Much/ better. 28uA when using the same sleep test. Wonder if I can get it down further.

Ive done a little bit of testing tonight. Running off the batteries I got a powrr consumption of 22uA. When I connected the battery to the 3.3av step up and used that to power the Atmel it increased to 81uA. 4 times as much.

I was playing around with my barebones last night (YJ), programming it with my USBasp. It was programming fine but as soon as it reset to actually run the sketch nothing happened. It would occasionally work when I switched the jumper on the USBasp to 5V instead of 3.3V.

Strangley plugging it into the battery worked fine. I think I shorted something on the programmer (I plugged the + and - into the - on the breadboard) and broke something on it.

Had another 1 (supposed to be 2, only 1 turned up) Atmel chip turn up but couldn't get that one to work at all.

This has been driving me nuts. I've been modifying the examples for the temperature sensor and radio to test switching them on and off and I could get them working. When I added it to my temp logger code things didn't work. AARRGGHHH!!

I /think/ I may have finally cracked it though. Not sure it is working 100% reliably though, I will have to test that. But I have something on a breadboard that consumes about 4uA when sleeping. Should last a while on batteries.

The radio works fine. It was the temperature sensor that was the pain! The 3.3V step up uses about 90uA not doing anything so I didn't want that going all the time.

I had forgotten I'd ordered this. I think I must have done it when I'd had too much wine. Turned up this morning. 10x Atmega328ps and crystals, caps, etc.

How much does that work out per complete unit?

£1.99 each from the UK.

I've also control  Light in the bedroom
(http://www.ledlightmake.com/led-lamp-c-77_78/e27-led-bulb5w-multicolored-rgb-16-colorwith-remote-control-p-203.html)with MCU(PIC12F675).

28 days later. No zombies. Wireless sensor still going strong. Should get at least another 2 months from it.

Added some CSS to my boiler interface so looks a little better. No mountains in the screenshot for Pete though.

NoSnowy :C

I like snowy mountains. Do you fancy a ski?

Nah, we're just good friends; it already has a partner, and I wouldn't want to get between them.

You don't want to upset a ski. I hear they can be dangerous and might kill you.

Well after not sorting the board for my timezone map I decided to do something useful with some of the LEDs. I made a dimable strip to go behind the bed-head. It worked quite well so I made a permanent board. Though they're bright white LEDs so it's a bit clinical.

Controlled via my home automation web remote, which tells a Raspberry Pi to transmit a 433 MHz signal. Different signals give different results. 100%/80%/60%/40%/20%/Off and Up & Down (by 10 units on the PWM scale).

Test breadboard:


Permanent board:
 

It is probably my best soldering attempt to date. Only made one mistake which was easily fixed.

Testing:

I take it it's linked to a g-sensor bolted to the bed and it decides what brightness it shines at depending on... you know...?
 :-O

 (hippo)

Well my battery optimising was worth it. My temp sensor has been running for 2.5 months on 2 AAs. I'm not sure if I checked it at the start, I probably did, but since the 24th of April the battery has stayed at 2.9V. It wouldn't make a very interesting graph.

How often are you transmitting? Is this using an RF24 transmitter?

Yup, using a nRF24L01+. Transmits between every minute and, er, 7 or 8 minutes. Depends if the temp has changed since last check.

Oh no, it's gone down by 0.1V. Not bad after 3.5 months. Not sure if it would have lasted slightly longer if there wasn't a power outage the day before yesterday and the sensor was trying to send to a switched off Pi for over 24 hours.