If you haven't already, you may want to go into PC Settings -> Privacy and explore the umpteen pages of options that are enabled by default to leach your data back to Microsoft and its advertisers. I did the 'custom options' install where I declined their offers to track me, but most of the stuff in Privacy was still switched on.
There's also a feature in Windows Update that uses the Win 10 install base as a bit-torrent swarm, and redistributes downloaded updates. I don't have an issue with that idea in principle, but as my upload is limited (if I go over my upload limit my download speed get's capped) it would have been nice for MS to mention it somewhere other than page 9,374,249 of the EULA.
I think I quite like 10, it's definitely an improvement on 8/8.1, and I'm pretty sure it's a lot better than 7 too. Not overly-keen with the intrusiveness of it, but with all the tracking stuff turned off I think it should be OK. If MS push things much more in that direction I think I'd be about ready to quit windows all together, tbh. But in terms of interface and speed, it's definitely a winner for me.
My laptop still refuses to reliably hibernate, though (first discovered on the day it came from the courier, manufacturer refused to acknowledge it as a fault) so at least I now know that it's not a Windows issue, but a hardware/driver issue. Power management driver perhaps? Who knows!
Got mine updated Thursday night. Haven't had much of of a play with it yet. My laptop actually hibernates (or rather resumes) better than it did before. The Intel grpahics driver did some stupid stuff when resuming in Win8 (7 worked fine). The display would go blank, come back for a bit, disappear, do that a few times and finally get to the desktop after a while.
Might have a play with it later (YJ) after changing the PCV hose on Sian's Mondeo. A split rubber hose that needs the inlet manifold removing to change it. Some of the bolts are impossible to get to. Grrrrr.
If you choose hibernate on mine it acts like it's hibernating, but when you boot up again it's a fresh boot. There's nothing in error logs etc. to say the hibernate failed. Sometimes it works, though.
I'm sure I used to have a computer that used to do that when trying to put it into standby. Never used the hibernate mode til I've had this laptop. And power options in the BIOS related to it maybe?
Had a fucking sod of a job changing the PCV hose on the Mondeo. Had to remove loads of electrical connections, clips for cables and hoses routed around it, 8 bolts holding it in place, 2 were fairly easy, 2 were awkward and the rest just couldn't be seen without holding my mobile with the camera switched on with the torch pointing between bits of car to direct myself on the screen. 2 big splits in it and the car is mostly back together now.
What does your Event Viewer show when tell it to hibernate? Mine says it is entering sleep, then returned from a low power state when it comes back.
Interestingly it also says:
The system firmware has changed the processor's memory type range registers (MTRRs) across a sleep state transition (S5). This can result in reduced resume performance.
whatever that means.
Haven't checked event viewer lately, but there wasn't much in as far as I recall.
As for bios settings, for a laptop that's supposed to be customisable, it's surprisingly locked down.
I discovered that MS balanced a bowl of water on the door for home network users upgrading to 10 who don't use homegroups but naively followed the recommended 'use your MS account details' for an ID and password.
It may not hit that many users, but from Windows 8 onwards if you use an MS account to log on and you want to view shares on other PCs on a home network that are also at 8 or above, Windows imposes a sort of bodged domain network model. You are required to enter an ID and password to view shares, your 'domain' is the name of your PC, and it royally screws things like network drives mapped to shares.
I never noticed this before because I had a mixture of boxes at 7 and 8. It's a pain to work round in 8 and 8.1 but relatively easy to switch to a local user in 10 if you know what the problem is and that this is the way to fix it. It wasn't something I'd ever seen publicised, and judging from the other bewildered users floundering around with half-arsed fixes, I'm not alone.
The issue is compounded because the 'join a domain or workgroup' wizard is broken for many users but in a way that gives the impression that something other than the wizard is broken - i.e. when you check the radio button to indicate that this is mainly a home PC and not business, the wizard hangs for a bit, tells you to restart (without asking what workgroup of domain you want), sets your work group back to the default 'workgroup' and when you restart you find that it's defaulted back to 'this PC is part of a business network'.
How does it work if you use a homegroup?
Can't say i've noticed any changes in how the network is handled from 8.1. When I did the upgrade install I'm sure my mapped drive to my Raspberry Pi showed up as normal :|
I couldn't say - I've never used a homegroup
As for the mapped drive thing, I assume you weren't running Windows 8 on your pi. The situation arises when a windows machine tries to see shares on another windows machine, both machines are at 8 or above and the one you're logged on to is using a Microsoft account (koswix@outlook.com etc.) as a user ID.