Reply to All
Show messages
Messages
Inbox
Search
Login
1–10
…
31–40
41–50
51–60
61–70
71
Christmas 2014
From: Chris (CHRISSS)
28 Dec 2014 11:48
To: koswix
57 of 71
41329.57
In reply to
41329.56
Well that's definitely a YJ.
From: fixrman
28 Dec 2014 14:59
To: Chris (CHRISSS)
58 of 71
41329.58
In reply to
41329.55
Quote:
The stand has a sponge in it to wipe the tip on.
Said the vicar to the acolyte.
From: Chris (CHRISSS)
28 Dec 2014 16:18
To: fixrman
59 of 71
41329.59
In reply to
41329.58
How's this looking? I think the problem I used to have was only trying very tip of the iron which just doesn't seem to heat up enough.
Attachments:
IMG_20141228_151641~01.jpg
From: Chris (CHRISSS)
28 Dec 2014 21:45
To: ALL
60 of 71
41329.60
Finished project. Mostly happy with the soldering apart from one or two where the contact point isn't fully covered in solder. And the motor mounts, struggled to get them to solder and don't like the way it's held in place.
Unfortunately one of the motors doesn't work so it just goes round in circles. Not sure it too much heat from the iron damaged the motor but I can see the brushes on the motor are in the wrong place and can't move them
:(
Attachments:
IMG_20141228_204140~01.jpg
IMG_20141228_204156~01.jpg
From: fixrman
29 Dec 2014 01:49
To: Chris (CHRISSS)
61 of 71
41329.61
In reply to
41329.59
Perfect! Solder still looks liquid, indicative of a good joint. A dry-looking, grainy joint is a cold solder joint and will fail, shiny and wet-looking = success! Excellent!
From: fixrman
29 Dec 2014 01:53
To: Chris (CHRISSS)
62 of 71
41329.62
In reply to
41329.60
The motors are hard to solder in place because the motor housing is heavier gauge metal. Heat the housing first so solder will melt on it, then place it next to the mount surface and heat them together, adding solder to the light side. Should do the trick.
Is there a way to reverse the polarity to that DC motor? I doubt the heat hurt the motor, it may be just defective. Did you test it first?
From: Chris (CHRISSS)
29 Dec 2014 12:13
To: fixrman
63 of 71
41329.63
In reply to
41329.61
:D
I am surprised how easy it was actually. I had read plenty of times that soldering is easy so not sure if it was the technique, iron or a combination of both but it was far easier than I was expecting from previous attempts.
I didn't think to try the motors before fixing them. Maybe I could get another and swap it over.
From: fixrman
29 Dec 2014 21:29
To: Chris (CHRISSS)
64 of 71
41329.64
In reply to
41329.63
Just make sure everything doesn't look like something to be soldered. You might cheese somebody off.
:-P
From: Wattsy (SLAYERPUNX)
30 Dec 2014 11:35
To: ALL
65 of 71
41329.65
Well met all of teh. This year was all about William so we have spent most of it making and playing with lego. I did get a new graphic novel (hedge knight by George r martin) and a newish pratchett non fiction book. Some money for my new gaming pc (anyone want to buy a GTX 670 for £100?) and a star wars mug.
In Taunton for a few days at the mo, went on a steam train yesterday and fossil hunting on a beach somewhere.
This holiday is going way to quickly for my liking.
Merry Christmas and a happy new year to one and all forumites and family's
From: fixrman
30 Dec 2014 12:42
To: Wattsy (SLAYERPUNX)
66 of 71
41329.66
In reply to
41329.65
Merry Christmas and HNY to you from across the pond.